Tumma

Dyno Results for the Body-Dropped and LT Swapped Chevy C10: Finnegan's Garage Ep.140 

Näkymät 244 t.
99% 2 416 21

There's a lot going on in today's episode. First, Newbern and I attempt to build new shelving in the shop and attach it to the concrete walls using a high-powered nail shooter, which doesnt work at all. In fact, the 2x4 wood falls right off the wall before we can ever stack any boxes onto the shelves. Since that wasn't working we decide to head to Mo's Speedshop in Dallas, Georgia, to fix the tune on my 1967 Chevy C10. It was running real bad and although it took several hours to figure out why, in the end the Chevrolet Performance LT4 made over 640 ft-lbs or torque at rear tires, which is awesome!
Here's a link to the crate engine that's under the hood of the C10:
sdparts.com/i-24134638-chevrolet-performance-19416595-supercharged-lt4-dry-sump-crate-engine-650hp-3-pin.html
Here's a link to the awesome sequential gearbox:
www.6xdgearbox.com/
and if you'd like the new Finnegan Speed and Marine C10 shirt or some stickers and a hat then go here:
www.fsmgarage.com
thanks for watching!
-Finnegan

Autot ja ajoneuvot

Julkaistu

 

4.04.2021

Jaa:

Jaa:

Ladata:

Ladataan.....

Lisää soittolistaan:

Oma soittolista
Katso myöhemmin
Kommentteja 100   
DibsRibs
DibsRibs 2 päivää sitten
For putting up those boards I would get some 3 inch concrete screws and just drill a hole big enough for the screws to fit in the 2x4s
Daniel Vrana
Daniel Vrana 5 päivää sitten
Molly bolts!!!! Red Heads!!!
C W
C W 8 päivää sitten
I love what you guys are doing just don,t drive past my house. It,s too damm loud and I,m old. I gotta take a nap.
Doc's GearHead Gaming
Doc's GearHead Gaming 8 päivää sitten
Just use nails in the wall's guys. Pre Drill your holes to the diameter of the nail's 3" spikes work good, Buy some hay wire, make a loop around the tip of the nail and wrap the wire down the nail. if done right when you drive the nail into the predrilled hole the wire will compress around the nail and fasten it securely to the wall. Just get it right the first time cause they are a pain to pull out once the wire is compressed lol
Loyd Courson
Loyd Courson 10 päivää sitten
You guys did it awesome!!
berky1976
berky1976 11 päivää sitten
I thought the transmission only required the clutch in first gear? Am I wrong there? I could have sworn that Finnegan said that when he intro'd the tranny back at the beginning of the build. I think I'll look up that episode and give it a watch.
Jessie Allen
Jessie Allen 12 päivää sitten
hey finnegan titan concrete bolts will be the magic you are looking for. ive used Ramset's, blue screws, red head wedge ancors. all will leave you pissed off.you need a roto hammer or hammer drill to predrill but once your hole is drilled you just put any impact gun on the proper sized titan bolt and run it in.if its not right put the impact in reverse and back it out and try again. totally reusable.
Jessie Allen
Jessie Allen 12 päivää sitten
ps tapcon are blue screws just dont they only work 25% of the time
R&S Machining & Welding
R&S Machining & Welding 12 päivää sitten
Thunbs down and wont watch because how does a car guy call it ft lbs of tq instead of lb ft of tq. Is this amateur hour over here or something
T Nelson
T Nelson 14 päivää sitten
About a $500 dollar shelf in the current day and age. Newbern has really grown on me, I like that guy! Good addition to the channel.
NICHOLAS RAMSAHAI
NICHOLAS RAMSAHAI 14 päivää sitten
Have Kevin Smith from KSR Performance take a look at it he's a Holley expert 👍🏻
Völl Däpp
Völl Däpp 14 päivää sitten
Screw anchors not common in the US?
Tim Ort
Tim Ort 17 päivää sitten
I've done alot of water proofing don't use a rams head when ya have any issues with water. I recommend tapcons they don't creator your concert also tapcons can be dipped in epoxy making it water tight.
J M
J M 20 päivää sitten
He should've been following Matt @ sloppy.. And or Faster Proms..
Larry Koziol
Larry Koziol 20 päivää sitten
I am guessing me face palming watching them build shelves would be the same as if they were watching me adjust a carb.
Larry Koziol
Larry Koziol 20 päivää sitten
To be a gearhead on some level & to not be a gun guy is such a foreign concept to me. The elegance of the mechanisms for both when properly executed are things of beauty. Whether we are talking a AKM, Jeep, Rolls Royce or Holland & Holland double rifle the work especially the handcrafted ones & design are amazing either in their simplicity, reliability or beauty.
Alex Crouse
Alex Crouse 21 päivä sitten
Do part throttle pulls!
CHEEKY YOUNG C#%TS Garage Media
In the thumbnail of this video your truck looks like it’s bent still the nose drops and the tub looks to be sloping back as well..
Heatshield Products Inc
Heatshield Products Inc 22 päivää sitten
Insight of the house is a good rule of thumb!
Flat Kangaroo
Flat Kangaroo 23 päivää sitten
Didn't know fsm stood for finnigan shelfs and maintenance
Mike Walsh
Mike Walsh 23 päivää sitten
Why on edge of the rollers like that? For a reason or does it not matter?
Brian Ickes
Brian Ickes 23 päivää sitten
👍
dropping Hertz
dropping Hertz 24 päivää sitten
It would probably Help if u used treated wood with the RamRoD lol..💪
djp73
djp73 24 päivää sitten
fiplace.info/loft/videot/g3ujppyto3jYao4
Edward Alamo
Edward Alamo 25 päivää sitten
Locite adhesive is better
83alpinab9
83alpinab9 25 päivää sitten
A couple of things with run ability stand out. Excessive crank time till it fires off. It should fire right away 5:32. When it stops pulling it shuts down entirely. Seems electrical. I suspect spark is missing on all cylinders when it happens. Something as simple as a bad engine block ground could cause this. I have been lucky in the past and maybe you sort out the extended crank problem and both problems go away. I had a car that ran fine until the exhaust was worked on, it turned out that the exhaust was the only ground for the engine block. When checking for spark it had no spark when testing it with the plug grounded at the engine but had spark when testing against the chassis. An inspection found a severed engine block ground..... easy fix, hard to pinpoint. Good luck and keep up the quality videos. Always fun to watch.
Heath Crow
Heath Crow 25 päivää sitten
Bakers racks are around $ 100. & they hold a ton of weight ! Much easier than wood
Heath Crow
Heath Crow 26 päivää sitten
Blue screws or concrete nails
BJ Johnson
BJ Johnson 26 päivää sitten
The 2x4 is too thick for that
Mike Norrod
Mike Norrod 26 päivää sitten
Finnigan can you update us the backfire under load with the C10 ,did you find a solution?
GaryLordsWayMinistry
GaryLordsWayMinistry 27 päivää sitten
Have you checked the Throttle sensor? To see if it is calibrated correctly or maybe even shorting out, causing the timing to go weird or tell the engine timing to go too far advanced or something? You know what they say: Lean is mean~!~
GaryLordsWayMinistry
GaryLordsWayMinistry 27 päivää sitten
Those ramset guns work better with a harder pin when the concrete is cured after 27 days as well as with a shot that is a magnum shell instead of the fresh concrete shot.
GaryLordsWayMinistry
GaryLordsWayMinistry 27 päivää sitten
You would be better off using a drill bit and a concrete wall anchor system for that shelf framing job you are trying to anchor to the wall. Those Ramset concrete pins work better when used to anchor wall floor bottom plates to the concrete to keep the bottom plate of wall framing from moving when kicked or hit so the wall will not move out of plumb. Maybe you should have studied a little bit before attempting this project. A little preparation would have gone a long way here to keep from looking like total armatures here.
scootbmx01
scootbmx01 27 päivää sitten
you can run a DI lt4 at like 13:1.
77 Zrod
77 Zrod 27 päivää sitten
Forced induction or high compression like to run 12.5:1 or higher air/ fuel ratio easily.
ausscorpio
ausscorpio 27 päivää sitten
So basically a blank that shoots the nail into the wall. OK. Also Have fun!!!!
George Merusi
George Merusi 27 päivää sitten
Can't wait to see this thing ripped at a HPDE track day
Richard Harvey
Richard Harvey 27 päivää sitten
It’s called a blank round.
Jimmy Barber
Jimmy Barber 28 päivää sitten
It's called a Hilti gun
Talisman1957
Talisman1957 28 päivää sitten
You got some catching up to do - 227 in 5th at 7600 rpm, and one more gear to go (T56 Magnum) fiplace.info/loft/videot/aW2LoqtolZfXaXo
GunPilot
GunPilot 28 päivää sitten
Cool, Jeff & Mo's tuned my 4.6L ford in my "58 F100. Works perfect!
Tory M Blue
Tory M Blue 28 päivää sitten
oh love the cage work, not going through the class, tight tight tight and great fitment through the dash. yes please! :)
James Nowell
James Nowell 29 päivää sitten
Just an FYI they like very tight plug gap. Like .018 tight
cory blum
cory blum 29 päivää sitten
on engine masters season one episode2, they had random misfires and tuning issues due to duel plane intake and fuel injector location / imbalance... was corrected when they installed a single plane intake... might be you issue... ask freiburger
W Kevin Long
W Kevin Long 29 päivää sitten
You don’t live far from me. Be happy to come by and tapcon the boards to your wall for you!😎
Sam Ram
Sam Ram 29 päivää sitten
Did you get your cell phone off the bed before driving home?
MRBLACK947
MRBLACK947 29 päivää sitten
Damn guys, The tuning by guesstimation thing is full sketch. That's a lot of money to blow up.
Rick Kelsch
Rick Kelsch 27 päivää sitten
I know that was bad just throwing stuff at it, lack of experience I guess.
TheBallznweenerz
TheBallznweenerz 29 päivää sitten
the hackery in this truck hurts my insides. makes for good videos i guess...
TheBallznweenerz
TheBallznweenerz 29 päivää sitten
it just makes me sad that everything is thrown together then youre surprised when it inevitably fails.
Radar Love
Radar Love 29 päivää sitten
Should have used a Hilti.
Raymond Farwell
Raymond Farwell Uukausi sitten
You have to push really hard to get that nail gun to get it to fire the round. That is the built in safety so someone just can't pull on the trigger have fire. They have three different power ranges the shell are color coded as the strength. I worked a job and they wanted a single door on the garage we held a eye beam up on 2x4 jacks and my boss used to big of a charge and blew the washer that on the nail right thru the hem fir 2x4. You also use use square cut nails and hammer them in with B F H. Mike you looked like you were ready for a moon walk. Love your hannel you guys have so much fun. Shifting your truck is so cool without using the clutch I wish I could shifted my 67 GTO that fast, I use to try, I got pretty fast but that was a long time ago
Matt Bouwman
Matt Bouwman Uukausi sitten
HAHHAA, feel like Brian O' Connor. If I dont like what it says, I'll say no and slam it shut
Chris W.P
Chris W.P Uukausi sitten
"I feel Like Brian O'Conner with my laptop in the passenger seat".... Was waiting to see the "Danger to manifold" message and sparks from the floor pan dropping out. Left disappointed. (Kidding! Awesome truck man)
Izzy Smith
Izzy Smith Uukausi sitten
No invite to the freedom 500?
Jordan Wiley
Jordan Wiley Uukausi sitten
Anyone else think at first they were gonna shoot the nails with a separate gun while trying not to hit mike?
Cameron Branch
Cameron Branch Uukausi sitten
You would have been better off with tapcons or expansion anchors.
Darren D
Darren D Uukausi sitten
It's all fun and games until the rear wheels grab the non rotating surface of the dyno
D- Wake
D- Wake Uukausi sitten
This was painful to watch...
Boomer ole bean Williams
Thank y'all, keep me rollin 😂😎
Stephen cummings
Stephen cummings Uukausi sitten
double shoot the nails and pl em
burt bacarach
burt bacarach Uukausi sitten
12x12 Dave in The Fast and the Firious....
Eric Romano
Eric Romano Uukausi sitten
Tradesmen every where is having a Field day with this one
Klaus Von Schmit
Klaus Von Schmit Uukausi sitten
Go by Home Depot and purchase 1/4” wedge anchors and shit can that Ramset on cured concrete especially, on a high “psi” strength concrete vertical surface! The only awesome thing about a ramset are using the 22 rounds to scare your buddies by sneaking up behind them with a squeezed round in your lineman pliers and then dropping perpendicular to the ground firing pin sticking out passed the end of pliers of the pliers an 1/8” inch..
moparsquid
moparsquid Uukausi sitten
WOW that's cool also did you see this magic box you put coins in and a cold drink comes out like magic
Shaun Roberts
Shaun Roberts Uukausi sitten
Tap Cons.... pre drill hole. There blue screws with a 10mm heads
James Smith
James Smith Uukausi sitten
Hey guys I’m a disabled veteran that has followed you and you have inspired me to completely rebuild my 1965 Chevy c 20 and I love your c10 project
Jared Breash
Jared Breash Uukausi sitten
The courageous language seemingly ban because architecture descriptively injure despite a ready hot. literate, superficial wall
Redman209
Redman209 Uukausi sitten
As a former cable guy the nail gun was a bit cringe. Anchor kits are so cheap and easy.
Max Torque
Max Torque Uukausi sitten
1st rule of tuning, don't try to get your transient and static fuelling correct at once! Do a SLOW accelerator tip in to move vertically up the load line at the engine speed fixed (this allows the dyno to lock onto and hold that speed, meaning you only move in ONE axis across the map) and do it slow enough to NOT trigger the transient fuelling (even better, zero all transient maps!). This allows you to both creep up on problem areas, and means you have some chance of understanding what is happening! Once your base map (with a warm engine) is within about 0.05 lambda, then you can start to look at the transient requirements, because you KNOW the steady state map is correct!
Mike Kendall
Mike Kendall Uukausi sitten
Use concrete anchors and a plug in hammer drill. The .22 nailer does not work well on the average concrete. 3/8 concrete anchor bolts are awesome.
fred rubble
fred rubble Uukausi sitten
cool truck finn
Daniel Cantrill
Daniel Cantrill Uukausi sitten
Chemical anchor is the absolute best method for what you were trying to achieve.
DontTreadOnMe9000
DontTreadOnMe9000 Uukausi sitten
Marty Ochs at Mo's is the Crown vic guru
Michael Kafoure
Michael Kafoure Uukausi sitten
Use tapcons they are screws for concrete. Drill a pilot hole with a hammer drill or the hammer drilling function on a cordless drill. They pretty well.
Bazooka Joe
Bazooka Joe Uukausi sitten
That is a really nice C10 build. I am also building a 1968 Chevy C10, but it is a original shortbed, fleetside,396 bigblock truck with TH400. I had thought about putting a LS engine in it but I think I will keep it bigblock and hopefully afford a big inch bigblock with procharger or other boost mod and just save the original stock engine. Anyways you are building a really awesome truck and it will be cool to watch the build come together.
Tony L
Tony L Uukausi sitten
Decided not to do any steady state tuning rather than power runs?
MrALTRD8
MrALTRD8 Uukausi sitten
Sounds like a good job for Kevin @KSR Performance to dial in the tune 👍
Tony Kemper
Tony Kemper Uukausi sitten
Newburn looks like he was in a car seat going to get ice cream with his daddy. Bad ass truck I can’t wait to see it at full potential.
Bret Hutchings
Bret Hutchings Uukausi sitten
Use Blue Screws man
jerry henderson
jerry henderson Uukausi sitten
Drill a hole in the cement , hammer an anker into the hole you drilled , and put the screw into the anker .
Nathan Bennett
Nathan Bennett Uukausi sitten
That nail gun is pretty fun to work with
Dad's Toy Garage
Dad's Toy Garage Uukausi sitten
Your truck sounds amazing! What mufflers are on it?
Flat4Buggy 2
Flat4Buggy 2 Uukausi sitten
They're the Bullet Race Mufflers from stainlessheaders.com
Garage It Yourself
Garage It Yourself Uukausi sitten
Um, aren't you supposed to do a whole bunch of part throttle tuning at different dyno loads to be able to build up your VE table? Once you've filled out a bunch of that then you can do full pulls. Trying full pulls without building up the VE table will cause problems and possibly damage the engine.
Garage It Yourself
Garage It Yourself Uukausi sitten
Um, aren't you supposed to do a whole bunch of part throttle tuning at different dyno loads to be able to build up your VE table? Once you've filled out a bunch of that then you can do full pulls. Trying full pulls without building up the VE table will cause problems and possibly damage the engine.
Steve Rone
Steve Rone Uukausi sitten
Hey, you should always use only pressure treated wood against concrete and you can even get fancy and use the “sill seal” foam
Miami Valley Small Bore
You should use Tapcon screws instead of a Hilti gun.
ShadowOps Airman1
ShadowOps Airman1 Uukausi sitten
I'd like to see a GMT800 Project (1999-2007) with the LS 4.8-6.0 (LR4, LM7, LQ4/9) with a 8l90 or 10l90 running the wheels.
ShadowOps Airman1
ShadowOps Airman1 Uukausi sitten
I had better control over one of those nail guns as a teenager lol.
bwizzle105
bwizzle105 Uukausi sitten
Danger to manifold!
Mike over cash
Mike over cash Uukausi sitten
Tap cons work better
Mike over cash
Mike over cash Uukausi sitten
Too strong of shot
Jon Hill
Jon Hill Uukausi sitten
Support 🇺🇲
72BRONCO351
72BRONCO351 Uukausi sitten
Hammer drill, 16d nail and rebar tie wire good to go
towboatjeff
towboatjeff Uukausi sitten
Pre drill and tapcon screws are what ya need
marcus king
marcus king Uukausi sitten
She level ?
BumDog2112
BumDog2112 Uukausi sitten
Tires that far forward on the rollers had me wincing. But man does that truck sound evil!!!
Michael Bare
Michael Bare Uukausi sitten
Newburn, I hope Mike buys you a lot of breakfast, lunch and dinner, you’re the only one I see working.
Larry Salisbury
Larry Salisbury Uukausi sitten
When you putting a load cell on the shifter
Rob Wagner
Rob Wagner Uukausi sitten
I'd just use Tapcons
Moto Cross
Moto Cross Uukausi sitten
Use tap cons, much stronger and less concrete fracturing.
twissted Jack
twissted Jack Uukausi sitten
Use Liquid nails and then Nail it. The glue is much stronger.
Ironwind1972
Ironwind1972 Uukausi sitten
0:08 what I sound like when I first wake up and lift my head off my pillow
Seuraava
Penkkiurheilija || BLOKESS
11:44
65 MILLION DOLLARS GENERATED
0:40
Näkymät 3,4 milj.
Penkkiurheilija || BLOKESS
11:44
65 MILLION DOLLARS GENERATED
0:40
Näkymät 3,4 milj.
Volvo's Key can do THIS!!
0:46
Näkymät 5 milj.